POSITION PURPOSEThe Quality Engineer is responsible for developing, implementing, maintaining and continuously. improving the organization Quality Management Systems (QMS), with strong emphasis in manufacturing process controls, quality engineering, risk management and process improvements.
The position works cross-functionally with Manufacturing, Engineering, Supply Chain, and Quality Control to ensure that Quality is built into the manufacturing process rather than relaying solely on final inspection to identify defects.
Quality Engineer will lead the development and implementation of quality engineering methodologies, including Process Failure Mode and Effects Analysis (PFMEA), Statistical Process Control (SPC), process capability studies (Cpk & Cp analysis) and supplier quality processes for improving at incoming.
The successful candidate will be hands-on spending time both on manufacturing and working on the development of technical quality systems. The position requires the ability to translate quality standards, customer requirements and engineering principles into practical manufacturing controls.
PRINCIPAL ACCOUNTABILITIESQuality Systems Development and Implementation- Develop and maintain process documentation, including Process Flow Diagrams, PFMEAs, Control Plans, Inspection Plans and Quality Procedures.
- Establish consistent methods for Process Control, verification, documentation and traceability.
- Support the development of Production Part Approval Process (PPAP), Production Quality Plans (PQP) and other customer-specific requirements as applicable.
- Ensure the quality controls are integrated throughout the manufacturing process
- Support Internal and Third-Party audits including identification of gaps against the standard, Corrective Action response and implementation
Manufacturing Process Quality Engineer- Work directly with manufacturing and engineering to identify potential process risk and implement preventive controls
- Evaluate manufacturing processes to identify sources of variation and opportunities for improvement
- Investigate recurring manufacturing defects and develop sustainable corrective actions
- Support process validation and new equipment validation as required (dry coil line)
- Participate in New Product Introduction, engineering changes and manufacturing process changes to ensure quality requirements are incorporated in manufacturing
Measurement System Analysis (MSA) and Metrology- Conduct and coordinate Gage Repeatability & Reproducibility (Gage R&R) studies
- Evaluate measurement methods, equipment suitability and measurement system variation
- Establish a proper measurement and inspection method for critical characteristics
- Support calibration system improvement and ensure measurement equipment is suitable for its intendent application
- Establish measurement system acceptance criteria and recommend improvements when measurement reliability is inadequate
Statistical Process Control- Develop and implement Statistical Process Control (SPC) methodologies when appropriate
- Conduct process capability studies, including Cp & Cpk analysis when appropriate
Supplier Quality and Incoming Inspection- Establish risk base incoming inspection methodologies
- Define inspection criteria based on product criticality, supplier performance and customer requirements
- Investigate supplier-related non-conformances and coordinate with Corporate the Supplier Corrective Action Response
- Work with Supply chain and purchasing to develop supplier quality metrics and improvement initiatives
Nonconformance and Corrective Action- Support investigation and Resolution of internal and external nonconformances
- Lead or facilitate root cause for significant or recurrent quality issues
- Ensure Corrective Actions address root cause and not just symptoms
- Evaluate effectiveness of implemented Corrective Actions
QUALITY CULTURE SCOPEQuality Engineer reports directly to the BAC Madera Quality Manager and works closely with Manufacturing. Engineering, Supply Chain, and Quality Team to integrate quality requirements into the daily activities.
The individual will provide technical guidance to specialists, supervisors, inspectors and personnel in general and promote preventive quality practices and the philosophy that quality is built into the process.
Participate in Manufacturing floor activities, continuous improvement activities and training activities to ensure effective implementation of quality controls
KNOWLEDGE AND SKILLS- Bachelor's degree in Mechanical Engineering, Electrical Engineering, Manufacturing Engineering, Quality Engineering, or related technical discipline
- Equivalent combination of technical education and relevant quality manufacturing experience may be considered
- 2-5 years' experience in quality engineering, manufacturing engineering or related quality function within a manufacturing environment
- Knowledge in ISO9001 and audit support
- Practical experience with PFMEA, Control Plans, Root Cause Analysis and Corrective Action methodologies
- Experience with MSA and Gage R&R
- Understandings of SPC, process capabilities (Cp / Cpk), PPAP and PQP
- Experience with 8D and/or A3
- Technical drawing interpretation (GD&T) with basic mechanical and electrical principles
- Microsoft office particularly Excell and data analysis tools.
- Experience with industrial equipment manufacturing mechanical assemblies, electrical controls, sheet metal fabrication, welding, power coating or similar manufacturing processes is preferred.
COMPETENCIES- BAC Cultural Values
- Customer Focus - Takes personal responsibility to achieve external and internal customer satisfaction
- Aligning People and Team Development - Use appropriate methods and interpersonal skills to develop, motivate and guide a team toward successful outcomes, meet business objectives, and attract and retain top talent.
- Leading Change - Continuously seek opportunities for different and innovative approaches to address organization challenges
- Execution - Get the job done through problem solving, driving for results, exercising control, setting high goals, and using measurement and accountability to continuously improve the business
WORKING CONDITIONS:The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodation may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this job, the employee is regularly required to stand and walk up to 50% of the time. Working conditions include those of a normal construction environment, as well as standard hazards associated with installed HVAC equipment and rotating equipment. This position requires occasional lifting of up to 50 lbs.