Application close date:
Applications will be accepted on an ongoing basis until the requisition is closed.
As a Senior Digital Hardware Engineer at Blue Origin, you will design and develop FPGA-based hardware for our next-generation RF communication and beamforming systems. You will be a hands-on schematic and signal integrity engineer, owning board-level FPGA hardware design from component selection through schematic capture and SI analysis, and providing technical oversight of internal or third-party PCB layout engineers and fabrication partners.
Responsibilities:- Design FPGA-based digital boards interfacing to beamforming ASIC carrier boards with high-speed control interfaces and precision clock distribution, digital interface and timing distribution boards connecting back-end processing to phased array antenna modules, and mixed-signal payload integration assemblies managing power, clocking, and inter-board data routing
- Create complete electrical schematics in Altium Designer for FPGA-based boards including I/O bank planning, power rail grouping, configuration circuitry, and JTAG/debug infrastructure
- Design multi-rail power distribution for FPGAs and ASICs including sequencing, point-of-load regulators, and power monitoring
- Select and evaluate components with consideration for performance, availability, and temperature range
- Define PCB stackup requirements in collaboration with fabrication partners, specifying laminate selection, copper weights, and layer assignments for impedance and loss targets
- Author routing constraint documents for high-speed interfaces (JESD204B/C, DDR4, LVDS) covering length matching, topology, spacing, termination, and reference plane rules
- Perform pre- and post-layout SI review using simulation tools (HyperLynx, SIwave, or equivalent) with particular attention to via stub effects, crosstalk, and connector transitions
- Review third-party layout deliverables against constraint documents and SI simulation results, providing clear and actionable feedback
- Support PDN analysis for FPGA and ASIC power rails
- Develop board bring-up procedures and test plans prior to first article fabrication
- Support hardware bring-up using oscilloscopes, logic analyzers, and BERT instruments to characterize high-speed interfaces
- Debug and document hardware issues, driving root cause analysis and design corrections
Minimum Qualifications:- B.S. in Electrical Engineering or related field with 5+ years of board-level hardware design experience
- Hands-on schematic design experience with high-performance FPGAs (Xilinx UltraScale+, Intel Agilex, or equivalent)
- Working knowledge of signal integrity fundamentals: transmission lines, impedance control, via effects, and termination - sufficient to author layout constraints and review third-party layouts
- Experience designing and validating high-speed serial interfaces at 16 Gbps lane rates or higher, with direct ownership of schematic and SI analysis at that rate
- Experience with at least one high-speed serial interface standard (JESD204B/C, PCIe Gen4/5, or equivalent) including schematic ownership
- Proficiency in Altium Designer for multi-sheet schematic design
- Familiarity with SI simulation tools (HyperLynx, SIwave, or equivalent) at a layout review level
- Hands-on bring-up experience with oscilloscopes, logic analyzers, and standard lab equipment
Preferred Qualifications:- Experience designing hardware for phased array or beamforming systems including phase array antenna module interfaces, array timing distribution, or beamforming ASIC integration
- Familiarity with JESD204B/C deterministic latency, SYSREF distribution, and multi-converter synchronization
- Familiarity or hands-on experience with Precision Time Protocol (PTP / IEEE 1588) or VITA 49.2 (VRT) in hardware implementations, including hardware timestamping, PTP-aware switch and PHY selection, clock recovery circuit design, or FPGA-based VITA 49.2 packetization and timing metadata
- Experience with mixed-signal or RF/digital PCB design
- Exposure to space, aerospace, or high-reliability hardware design environments
- Experience working with and technically directing third-party PCB design or EMS partners
- Experience analyzing and mitigating EMI/EMC challenges inherent to mixed-signal boards combining GHz-rate digital signals with sensitive analog and RF circuitry
Compensation Range for:
WA applicants is $197,529.00 - $276,539.55
Other site ranges may differCulture StatementDon't meet all desired requirements? Studies have shown that some people are less likely to apply to jobs unless they meet every single desired qualification. At Blue Origin, we are dedicated to building an authentic workplace, so if you're excited about this role but your past experience doesn't align perfectly with every desired qualification in the job description, we encourage you to apply anyway. You may be just the right candidate for this or other roles.
Benefits- Benefits include: Medical, dental, vision, basic and supplemental life insurance, paid parental leave, short and long-term disability, 401(k) with a company match of up to 5%, and an Education Support Program.
- Stock Options for all regular employees (working at least 20 hours/week)
- Paid Time Off: Up to four (4) weeks per year based on weekly scheduled hours, and up to 14 company-paid holidays.
- Dependent on role type and job level, employees may be eligible for benefits and bonuses based on the company's intent to reward individual contributions and enable them to share in the company's results, or other factors at the company's sole discretion. Bonus amounts and eligibility are not guaranteed and subject to change and cancellation. Please check with your recruiter for more details.
